Tips

What does washing machine say?

Pin
Send
Share
Send
Send


Modern washing machines are not only ready to save us from unpleasant and hard physical work. They are also able to carry out self-diagnostics and to signal about any malfunctions - true, in their machine language. Although in most cases it is impossible to do without the help of an experienced master who is able to provide professional help to an intelligent mechanism, you can help yourself in certain situations with your washing machine (hereinafter referred to as CM) if you understand what it is asking for. The error code can be issued by the smart technician via the LCD display (if there is one) or through flashing indicators. Below are the error codes of the most popular brands (Atlant, Gorenje, ASKO, Samsung, Indesit, Ariston, Hansa, Candy, Kaiser, LG, Electrolux, Zanussi).

Error Codes washing machines Indesit, Ariston

F01 - Signal of problems in the operation of the drive motor due to a short circuit in the control circuit
F02 - The system notifies of the absence of a signal about the operation of the motor from the tachogenerator to the electronic controller
F03 - Problems in the operation of the temperature sensor (sensor failure or sticking of the heater)
F04 - The system signals a malfunction of the pressure switch (water level sensor)
F05 - The washing machine does not drain the water - problems in the operation of the water discharge system (the water level sensor is faulty - it does not give an "Empty tank" signal after draining the water or the drain pump does not function)
F06 - Button malfunction in the "Ariston Dialogic" CM series
F07 - The system indicates that the heating element (PETN) is not immersed in water
F08 - This code indicates a failure of the heating element (sticking of the relay): the sensor simultaneously generates 2 signals "Empty tank" and "Overflow"
F09 - The system informs about a failure in the electronic control system (there may also be problems with the non-volatile memory of the processor)
F10 - Failure of the water level sensor: the system did not receive a signal about the status of the working tank (tank and not empty and not full)
F11 - The system has problems in the operation of the drain pump - there is no information about its condition (check the pump connection)
F12 - There is no communication between the control system (electronic controller) and the display module (selector)
F13 - Signal about problems in the work of drying (CM series "Margarita 2000"): the control network t0 is faulty
F14 - Signal about problems in the work of drying (CM series "Margarita 2000"): drying does not turn on
F15 - Signal about problems in the work of drying (CM series "Margarita 2000"): drying does not turn off
F17 - Problems with the locking lock (the door is not tightly closed or the door is open)
F18 - Microprocessor failure

Error codes washing machines Candy

E01 - The system has detected a malfunction of the locking device of the CM door (the door is not locked, the indicators do not light up)
E02 - Signal about problems in the water filling system (the water level does not reach or exceeds the nominal), possible causes: valve malfunction, filter clogged
E03 - Signal of problems in the water discharge system (no drain or no drain time is exceeded)
E04 - Signal about problems in the water loading system (water level exceeds the established norm)
E05 - The system signals about problems with the temperature sensor - there is no water heating, the wash does not stop
E07 - The system signals the problems of the drive motor - the tachogenerator is faulty
Е09 - The system signals about problems of the drive motor (the shaft does not rotate) - problems with control

Error codes washing machines ASKO

E 01, "Motor fault" - General error: a problem occurred in the operation of the drive
E 02, "Water inlet fault" - Problems of water recruitment
Е 03, "Draining fault" - Problems of water discharge
E 04 - CM cannot provide sufficient water supply (it is recommended to check the condition of hoses, filters)
E 05, E 06 - There were problems with water heating
"Door lock fault" - Check the status of the locking hatch (the door is not tightly closed)
"Floaming" - The system signals increased foaming
"Overfilling", "Over flov" - Notice of excess water level (overflow) in the working tank CM
"Termistor fault" - defective temperature sensor
"Pressure sensor error" - Faulty level water sensor

Error codes washing machines SAMSUNG

E 1 - An error occurred while typing water
Е 2 - СМ notifies on the problems that have arisen while draining water from the system (the time for draining the water does not correspond to the one set by the manufacturer)
E 3 - The system warns that when filling the water reached the level of "overflow"
DE, DOOR - Check the locking of the hatch (the door is not tightly closed)
E 4 - The number of loaded laundry in the working drum does not meet the established standards
E5, E6 - Water heating problems
E7 - Water level sensor is not functioning.
E 8 - Temperature is not observed (t0 of water does not meet the established rate)
E 9 - This message will appear if the system has detected a water leak or spontaneously drained 4 times in a row (to the level safe for the heater)

Error codes washing machines LG

RE - Error detected in the work of the water level sensor
FE - The system reports that the working tank is overfilled with water.
dE - Door interlock: check that the door is tight enough
IE - Problems with water recruitment (CM can not get water in the tank)
OE - Problems with the drain (check the condition of the hose and filter)
UE - Drum malfunction (unbalanced)
tE - Temperature disturbed
LE - Locking Mechanism Detected
CE - System notifies motor drive overload
E3 - The system cannot determine the load.
AE - Failure in the system of auto power off CM
E1 - Water leak in pallet detected
HE - Failure of heating heater
SE - Drive Motor (Hall Sensor) Error Found

Error codes washing machines KAISER

E 01 - The system did not receive a signal to close the door from the limit switch of the lock - the wash will be stopped.
Е 02 - This code will appear if the filling time of the working tank has exceeded 2 minutes. At the same time, the SM continues the washing program, but blocks the filling mode above the nominal level (an error is issued after performing the washing operation).
E 03 - Drain water took more than 1.5 minutes. In this case, the washing continues, the SM automatically reduces the spin speed to 400 rpm and gives an error code at the end of the program.
E 04 - Problems with filling water: when problems are detected (the level sensor detects "Tank overflow"), the system stops washing, issues an error code and starts the drain pump. If the pressure switch gives an "Empty tank" signal, the drain pump automatically shuts off, otherwise the pump continues to work.
E 05 - Problems with loading water: an error is displayed if after 10 minutes from the moment of filling the working tank the system does not receive the "Nominal level" sensor signal. The wash stops.
E 06 - Problems with water discharge: an error is displayed if after 10 minutes of operation of the drain pump does not receive the “Empty tank” sensor signal. The wash stops.
E 07 - The system has detected a leakage of water into the CM tray (the Aqva Stop mechanism is triggered). The wash stops and the drain pump turns on, which works until the “Empty Tank” signal is received.

E 08 - CM warns that the parameters of the power supply network do not correspond to the norm (the manufacturer recommends a voltage of 190-253 V with a frequency of 50-60 Hz)
E 11 - Malfunction in the hatch locking system, washing is interrupted
E 21 - Problems occurred in the drive system (lack of signals from the tachogenerator). Washing is interrupted
E 22 - The system records the unauthorized rotation of the drive motor (in the absence of a start command). Washing stops
E 31 - Occurrence of a temperature sensor malfunction (short circuit in the circuit). The error is displayed after the completion of the washing program.
E 32 - Failure of temperature sensor (open circuit). The error is displayed after the completion of the washing program.
E 42 - Malfunction - after completion of washing the hatch is blocked for more than two minutes

Error codes washing machines ELECTROLUX and ZANUSSI

CM with control system EWM1000
E 11 - Problems with loading water (the required level in the working tank was not reached within the time set by the manufacturer)
E 13 - The system has fixed the leakage of water in the pan SM
E 21 - Problems with discharge: water has not been removed from the working tank for 10 minutes
E 23 - Problems with draining: the system detected a breakdown of the triac (control element) of the drain pump
E 24 - Drainage problems: the system has detected malfunctions in the operation of the drain pump triac circuit
E 33 - The system signals the malfunctioning (inconsistent) operation of the water level sensors (level sensor I and a sensor warning against switching on the heating element in the absence of the required amount of water)
Е 35 - Problems with loading water: in fact, the water level in the working tank is higher than the permissible
E 36 - Failure of the sensor, warning against turning on the heating element in the absence of the required amount of water (AB S)
Е 37 - Breakdown of the water level sensor І (L1 S)
E 39 - Breakdown of the water overflow level sensor (HV 1 S)
E 41 - Error notifies that the door of the CM is open or not closed tightly.
E 42 - The system has detected a malfunction of the locking lock of the hatch
E 43 - Breakdown of the control element (triac) of the lock
E 44 - A hatch closure sensor has been detected
E 45 - The system signals detected violations in the control circuit of the hatch lock (in the electronic controller)
E 51 - Problems with the drive motor (short circuit of the control element - triac)
E 52 - Lack of contact between the electronic controller and tachogenerator
E 53 - The system signals the detected violations in the control circuit of the drive motor (in the electronic controller)
E 54 - “sticking” detected by one of the two contact groups of the reversing relay of the driving motor
E 61 - Violation of the temperature regime: when heated, the water does not reach the temperature set by the program for the standard time
E 62 - Violation of the temperature regime: when heated, the water reached a value above + 880С in 5 minutes
E 66 - Fault of relay of TENA is fixed
E 71 - The system reports inadequate operation of the temperature sensor (increased resistance)
Е 82 - Problems found in the operation of the selector (device for selecting programs and cycles)
E 83 - An error was detected while reading data from the selector (the code is displayed only in diagnostic mode)
E 93 - Found CM configuration error

CM with control system EWM2000
E 11 - Signal about the problems with the filling of water when washing clothes
E 11 - Signal of problems with filling water when drying clothes
E 21 - Signal of problems with water discharge
E22 - Signal of problems with water discharge in the mode of drying clothes
E31, E32, E33, E34 - Signal about problems related to inconsistent operation of level sensors (prosostats)
E41, E42, E43, E44, E45 - Failure of the hatch locking system alarm
E51 - The system signals malfunctions of the drive motor control element
E52 - Tacho generator malfunction detected
E53 - Malfunction detected in the motor control system
E54 - A malfunction was detected in the operation of one of the electronic controller relays
E61 - Violation of temperature: the system recorded a slow heating of the water in the working tank
E62 - Violation of temperature: the system recorded an unregulated high t0С of water in the working tank
E63 - The system displays problems in the SM operation in the drying mode (insufficient heating)
E64 - The system displays problems in the SM operation in the drying mode (overheating)

Error codes washing machines Hansa

SM Series RA
E01 - Faulty door lock (no lock). The washing program is interrupted (in case of absence of blocking - after 2 seconds, in case of failure of the limit switch - after 10 seconds)
E02 - Malfunction of the water level sensor: there is no signal that the water level has reached I, washing stops.
E03 - Drainage system malfunction: there is no signal from the sensor that there is no water. CM locks the hatch to completely shut down the unit.
E04 - Overflow of the working tank: in this case, the CM automatically interrupts the washing and turns on the drain pump. The hatch remains locked until the machine is completely turned off.
E05 - The system signals a malfunction in the temperature sensor: water heats up by less than 40 after 10 minutes of operation of the heating element (due to a short circuit or interruption) or does not comply with program standards. Washing continues without water heating.
E07 - The system records in the washing mode the absence of contact of the control element (electronic controller) with the tachogenerator. Washing stops.
E08 - The system records in the spin mode the absence of contact of the control element with the tachogenerator. Stop the cycle.
E10 - The system fixes the discrepancy between the parameters of the power supply network (voltage, frequency). Washing stops.
E11 - Malfunction (short circuit) of the control element (triac) of the driving motor is detected. Washing stops.
E12 - The system detects the leakage of water into the SM tray (thanks to the signals from the AQUA STOP sensor). The drain pump works, the lock of the hatch is blocked. The door opens after receiving the "Empty Tank" signal.
E14 - Failure of the electronic controller. Washing stops.
E15 - When turning on the power or after selecting the wash mode, a malfunction of the electronic controller was detected.

SM PC series
E01 - The system signals the absence of a control signal to enable the door lock lock
E02 - Signal about problems with water in bulk (time filling the working tank to the nominal level exceeded 2 minutes)
E03 - Signal of problems with water discharge (time to drain the water from the working tank exceeded 1.5 minutes)
E04 - Signal about problems with water in bulk (the pressure switch gives a signal that the working tank is overflowed)
E05 - Signal about problems with water in bulk (time filling the working tank to the nominal level exceeded 10 minutes)
E06 - Signal of problems with water discharge (for 10 minutes no empty tank signal is received from the pressostat)
E07 - The system detects the leakage of water into the CM tray (thanks to the signals from the AQUA STOP sensor).
E08 - The system fixes the discrepancy between the parameters of the power supply network (voltage, frequency).
E09 - Excess foaming in the "spin" mode, with which the system could not cope
E11 - The system reports a malfunction of the triac (control element) of the power supply circuit of the locking mechanism of the hatch
E21 - Malfunction of the drive motor (there is no connection with the tachogenerator, blocking the operation of the motor)
E22 - Malfunction of the drive motor (unauthorized rotation)
E31 - Detected a malfunction of the temperature sensor (short circuit)
E32 - Detected malfunction of the temperature sensor (open circuit)
E42 - Failure of the locking mechanism
E52 - Failure of the machine’s autonomous memory

Error codes washing machines GORENJE

F1 - CM is trying to tell you that there is an open or short circuit in the temperature sensor circuit.
F2 - This code notifies that the required amount of water has not entered the tank during the time set by the manufacturer (check the condition of the hose and the filter on the water supply)
F31 - Notification that the electronic controller is not receiving signals (problems with the tachogenerator)
F32 - Problems in the drive motor control system
F4 - (temperature mode)
This code notifies that during the time set by the manufacturer the temperature of the water in the working tank has not warmed to the specified level
F41 - In this case, the actual temperature of the water in the tank has risen above the permissible value.
F43 - CM reports that the rate of increase in water temperature is not correct (higher than the allowable value)
F5 - Problems with discharge: in this case, the CM cannot ensure the discharge of water, or for the allotted period of time the mechanism could not reach the “Empty Tank” position
F61 - SM could not provide the specified speed of rotation of the drum in the "Spin" mode
F63 - There were problems with control: the electronic controller does not receive signals from the electronic mechanism of the drive motor

Error codes washing machines Atlant

"door" - Everything is simple here: problems with the door - you could not close it tight enough, so the machine does not want to be washed. But this inscription may indicate a malfunction of the locking electric lock, and in the most difficult cases, problems with the electronic module.
F2 - By issuing such a code, the machine reports that there are problems with the temperature sensor (the “innocuous” version), with heating heating elements or with the control module.
F4 - Washing machine does not drain. Make sure that the drain hose is properly connected, check that the drain pump filter is not clogged, and the condition of the pump itself: the impeller should rotate completely freely.
F5 - This inscription can be highlighted while simultaneously drawing and draining water. In this case, check the condition of the drain hose (by analogy with the situation described above) and make sure that the water supply is adequate. Имеется в виду достаточное давление - причина может крыться в фильтре подачи (убедитесь, что он не забился).
F6, F9, F12 - Исправить поломку сможет только мастер: речь идёт о проблемах электродвигателя или электронного управления
F8 - В баке СМ - повышенный уровень воды. Следует обратить внимание на датчик уровня и состояние электроклапана.
SEL - это сокращённое "селектор", т.е. модуль интерфейса Вашей СМ. Появление этой надписи означает, что возникли проблемы с переключателем программ (СМ также может просигнализировать об этом с помощью мигания индикаторов, как это обычно происходит в конце стирки).
F13 и F14 - Возникли неполадки с электронным модулем

Pin
Send
Share
Send
Send